A water filter is an important appliance in any household as it helps to make sure that the water we drink is clean and free of contaminants. PUR is a popular brand of water filter, and like all appliances, it may sometimes experience issues.
One common problem with PUR water filters is the red blinking light, which can be confusing and worrying for users. In this article, we will discuss the possible causes of the red blinking light on a PUR water filter and how to troubleshoot and fix the problem.
How to Reset the Red Light of PUR Water Filter?
There are a few different steps you can try to reset the red light on your PUR water filter:
Check the filter:
The red light may be indicating that the filter needs to be replaced. Check to see if the filter is still within the recommended lifespan or if it has exceeded the recommended usage. If the filter needs to be replaced, follow the manufacturer’s instructions for replacing it.
Increase water pressure:
If the water pressure is too low, it can cause the red light to come on. Try increasing the water pressure by cleaning the inlet screen or checking for any restrictions in the water line.
Reset the system:
If the red light persists after checking the filter and increasing the water pressure, try resetting the system. To do this, turn off the water supply to the filter and unplug the unit. Wait a few minutes, then turn the water supply back on and plug the unit back in. The red light should reset and the filter should be ready to use again.
If none of these steps work, there may be an issue with the electrical system of the water filter. In this case, it may be necessary to contact the manufacturer or a professional for further assistance.
Why Red Light Blinks in PUR water
Causes:
There are a few different causes of the red blinking light on a PUR water filter:
Filter needs to be replaced:
The red light may be indicating that the filter needs to be replaced. Check to see if the filter is still within the recommended lifespan or if it has exceeded the recommended usage.
Water pressure is too low:
If the water pressure is too low, it can cause the red light to come on.
Electrical issues:
There may be an issue with the electrical system of the water filter. This could be caused by a problem with the unit itself, or it could be due to a problem with the electrical outlet or the wiring in the home. If none of the other troubleshooting steps have worked, it may be necessary to contact the manufacturer or a professional for further assistance.
Solutions:
To check, and replace the filter on your PUR water filter, follow these steps:
- Locate the filter: The filter is usually located inside the water filter unit, either at the bottom or on the side. Consult the user manual for the specific location of the filter on your model.
- Remove the filter: Depending on the model, you may need to use a tool to remove the filter. Consult the user manual for the specific instructions for your model.
- Inspect the filter: Once the filter is removed, inspect it for any visible damage or contamination. If the filter looks dirty or damaged, it needs to be replaced.
- Replace the filter: Follow the manufacturer’s instructions for replacing the filter. This usually involves inserting the new filter into the water filter unit and securing it in place.
- Reset the system: Once the new filter is in place, reset the system by turning off the water supply to the filter and unplugging the unit. Wait a few minutes, then turn the water supply back on and plug the unit back in. The red light should reset and the filter should be ready to use again.
Increase water pressure
There are a few different steps you can try to increase the water pressure in your PUR water filter:
Clean the inlet screen:
The inlet screen is located on the inlet valve of the water filter unit. It is responsible for filtering out dirt and debris from incoming water. If the inlet screen is dirty or clogged, it can restrict the flow of water and cause the pressure to drop. To clean the inlet screen, follow these steps:
- Turn off the water supply to the filter.
- Locate the inlet valve and remove the inlet screen.
- Rinse the inlet screen with clean water and gently scrub it with a soft brush to remove any dirt or debris.
- Reinsert the inlet screen and turn the water supply back on.
Check for restrictions on the water line:
If the water pressure is low throughout the house and not just at the water filter, there may be a restriction in the water line. Common causes of restrictions include kinks in the hose, clogs in the pipes, or damaged pipes. If you suspect there may be a restriction in the water line, it may be necessary to call a plumber for further assistance.
Check the water pressure regulator:
The water pressure regulator is a valve that controls the flow of water into the house. If the water pressure regulator is set too low, it can cause the water pressure to drop. To check the water pressure regulator, follow these steps:
- Locate the water pressure regulator, which is usually located on the incoming water line near the main water shut-off valve.
- Use a water pressure gauge to test the water pressure. The recommended water pressure for most homes is between 40 and 60 PSI.
- If the water pressure is below the recommended range, adjust the water pressure regulator accordingly. Consult the manufacturer’s instructions.
Electrical issues and resetting the system
If none of the other troubleshooting steps have worked and the red light on your PUR water filter persists, there may be an issue with the electrical system. To check for electrical issues, and reset the system, follow these steps:
Check the electrical outlet:
Make sure the electrical outlet is working properly by plugging in another appliance to see if it powers on. If the outlet is not working, check the circuit breaker or fuse box to see if the circuit has been tripped or a fuse has blown.
Check the wiring:
If the outlet is working and the circuit is not tripped, there may be an issue with the wiring. Check the wiring for any visible damage or loose connections. If you suspect there may be an issue with the wiring, it is recommended to call a professional electrician for further assistance.
Reset the system:
If you have ruled out any issues with the filter, water pressure, or electrical system, try resetting the system. To do this, turn off the water supply to the filter and unplug the unit.
Wait a few minutes, then turn the water supply back on and plug the unit back in. The red light should reset and the filter should be ready to use again. If the red light persists, it may be necessary to contact the manufacturer or a professional for further assistance.
Also Read: Clean Water Filter Cartridge-Best Guide
Conclusion:
In conclusion, a red blinking light on a PUR water filter can be caused by a variety of issues, including a filter that needs to be replaced, low water pressure, or electrical problems.
By troubleshooting and addressing the issue, you can make sure that you continue to have clean, safe drinking water. To fix the problem, start by checking and replacing the filter if necessary, increasing the water pressure, and checking for electrical issues.
If none of these steps work, try resetting the system. If the problem persists, it may be necessary to contact the manufacturer or a professional for further assistance.
My name is Manan Bukhari and I am an expert in reviewing kitchen products for years. I have a passion for testing multiple gadgets especially related to home & kitchen. I love to spend my free time in resolving issues if I face some in any of my daily use things. I have fixed multiple gadgets of my home on my own without any assistance and that thing gave me confidence to make a blog on troubleshooting of items that are for daily use to assist you folks. Even my wife praises me for having such talent. I always explore new machines on my own because this thing fascinates me.
